SypherTec
…
PART 2 · 07 OF 084 MIN READUPDATED 20 NOV 2026

Functions: Naming a Set of Steps

Four lines of your report print a label and an amount the same way: Total spent, Biggest spend, Smallest spend and Budget. This lesson writes that pattern once, as a function of your own, and uses it four times.

The concept

Here is your tracker as the last lesson left it. Run it:

WHERE YOU LEFT OFF · PYTHON
Tab indents. Press Escape, then Tab, to leave the editor.
CONSOLE
no output

Now run this:

ONE FUNCTION, TWO CALLS · PYTHON
Tab indents. Press Escape, then Tab, to leave the editor.
CONSOLE
no output

Two report lines from one piece of code. The block starting with def creates a function called print_line. You have used functions since the first lesson: print, len, sum. Now you can write your own.

Each line at the bottom is a call. print_line("Total spent", 12500) runs the function's block with label set to "Total spent" and amount set to 12500. The second call runs the same block again with different values.

Defining a function and running it are two separate steps. Run this:

DEFINED, BUT NEVER CALLED · PYTHON
Tab indents. Press Escape, then Tab, to leave the editor.
CONSOLE
no output

Only the line outside the function printed. def stores the steps under a name, and nothing in the block runs until you call it. To run it, you would write say_hello().

The syntax

def print_line(label, amount):
    print(f"{label}: ₦{amount:,}")
  • def, the function's name, parentheses, and a colon.
  • Inside the parentheses are the parameters: names the block can use. Separate them with commas.
  • The block is indented four spaces, like every other block.

To call it, write its name and the values to use:

print_line("Budget", 15000)

The values in a call are the arguments. They fill the parameters in order: the first argument goes into the first parameter, the second into the second.

Function names follow the same rules as variable names. A good one starts with a verb that says what it does: print_line, not line.

Define functions at the top of the file, so they exist before any line calls them. Python style leaves two blank lines after a function, to set it apart from the code below.

A minimal working example

main.py
def print_line(label, amount):
    print(f"{label}: ₦{amount:,}")
 
 
print_line("Total spent", 12500)
print_line("Biggest spend", 4200)
print_line("Budget", 15000)

Output: three report lines, all in the same format. To change that format, for example to add a full stop, you would change one line in the function, and every call would follow.

Common mistakes

You call the function before it is defined. Run this:

CALLED BEFORE IT IS DEFINED · PYTHON
Tab indents. Press Escape, then Tab, to leave the editor.
CONSOLE
no output
NameError: name 'print_line' is not defined

Python runs top to bottom, and def is a line like any other. When the call on line 1 runs, the def below it has not run yet, so the name does not exist. Move the function to the top of the file.

You leave out an argument. Run this:

ONE ARGUMENT MISSING · PYTHON
Tab indents. Press Escape, then Tab, to leave the editor.
CONSOLE
no output
TypeError: print_line() missing 1 required positional argument: 'amount'

The call must give one argument for each parameter. Python names the one that has no value. Give too many and you get the opposite: print_line() takes 2 positional arguments but 3 were given.

You leave off the parentheses. print_line on its own line gives no error, and does nothing. Without parentheses you are only naming the function, not calling it. A call always has parentheses, even when there are no arguments: say_hello().

Try it yourself

You will write print_line and use it in place of four report lines.

  1. Run the starting code below. Find the four lines that print Total spent, Biggest spend, Smallest spend and Budget.

  2. At the very top of the file, above owner, add:

    def print_line(label, amount):
        print(f"{label}: ₦{amount:,}")
     
     

    That is the function, then two blank lines. Run it. Confirm nothing changed: defining a function prints nothing.

  3. Replace your Total spent print with print_line("Total spent", total). Run it. Confirm the line looks the same as before.

  4. Replace the other three in the same way: print_line("Biggest spend", biggest), print_line("Smallest spend", smallest) and print_line("Budget", budget). Run it. Confirm your whole report looks exactly as it did in step 1.

  5. Break it on purpose: change print_line("Budget", budget) to print_line("Budget"). Run it. Confirm the console shows a TypeError that names the missing 'amount'.

  6. Fix it: put , budget back. Run it. Confirm your report returns.

TRY IT YOURSELF · PYTHON
Tab indents. Press Escape, then Tab, to leave the editor.
CONSOLE
no output

Your function prints a line, and that is all it does. Its result goes straight to the screen, so the rest of your program cannot use it. The next lesson writes a function that hands a value back.

QUIZ · 3 QUESTIONSCheck what stuckStart the quiz
PART 2 · 07 OF 08❮❯